Complete Electrical Rewiring & Apartment Installation

Clear warning signs experienced by homeowners in older properties include tingling electrical shocks when touching metallic appliance casings, audible sizzling and burning plastic smells from distribution boards, flickering room lights whenever heavy appliances cycle on, and frequent circuit breaker trips. In structures exceeding 30 years of age, in-wall cloth-covered or vulcanized rubber-insulated wires harden, dry out, and crack under ongoing thermal cycling, exposing live copper conductors to surrounding masonry and adjacent cores. This induces invisible micro-arcing, in-wall fire propagation, and unaccounted electric utility billing losses.

When undertaking a full rewiring project, conduit pathways are inspected using digital borescopes and flexible draw springs. Where buried in-wall PVC conduits remain intact, old decayed wires are extracted without plaster demolition and fresh Halogen-Free conductors pulled through using non-conductive pulling lubricants. Where conduits are blocked or collapsed, wall chasers equipped with vacuum extraction cut clean narrow chases, or architectural skirting trunking is deployed seamlessly with minimal dust and structural impact.

In modern residential electrical installations, occupant fire survival depends directly on conductor flame-retardancy classifications. We exclusively deploy certified Low-Smoke Zero-Halogen (LSZH) NHXMH and N2XH solid electrolytic copper cables from Hes Kablo, Nexans, or Prysmian that emit zero toxic acid gases and minimal smoke under open flames. Circuit cross-sections are strictly dimensioned: 3x1.5mm² for lighting branches; 3x2.5mm² for general socket rings; dedicated 3x2.5mm² or 3x4mm² for air conditioners, ovens, and water heaters; and 3x6mm² or three-phase 5x6mm²/5x10mm² for main consumer unit riser feeds.

International electrical color coding is strictly enforced across the entire installation: Brown, Black, or Grey for live phases; continuous Light Blue for operational neutral; and strictly Green-Yellow for protective earthing conductors. Hand-twisted tape splices inside junction boxes are entirely prohibited, replaced with genuine V0 flame-retardant Wago 221 lever connectors.

Over 70% of residential electrical fires originate from severe thermal overloads inside kitchens and bathrooms. Operating an air fryer, microwave oven, rapid kettle, dishwasher, and electric oven simultaneously draws continuous current exceeding 30 Amps. In our rewiring projects, kitchen loads are never combined onto a single run: dedicated 3x2.5mm² runs feed the oven (C16 breaker) and dishwasher (C16 breaker), countertop outlets are split into dual independent socket groups, and induction hobs receive heavy 3x4mm² wiring (C25 breaker), eliminating thermal hazards.

In bathrooms, rising shower humidity is sealed out by potting all ceiling junction boxes inside IP68 dielectric silicone gel enclosures. Washing machine, electric water heater, and whirlpool circuits terminate onto dedicated high-sensitivity 10mA or 30 mA RCBO breakers at the consumer panel, ensuring absolute shock protection on wet tiles.

When rewiring furnished and occupied properties, families worry about prolonged power outages and disruption. ElektrikçiGO certified technicians execute a structured 'Progressive Room Isolation Protocol': On Day One, a temporary safety board is commissioned to keep the refrigerator, broadband router, and essential lighting continuously powered. Work advances methodically through the living room, kitchen, bedrooms, and bathrooms; at the end of each working day, completed rooms are tested, energized, and cleaned, ensuring residents are never left in the dark overnight.

In modern open-plan offices, corporate plazas, and commercial premises, power and structured data infrastructure distribute across raised-floor cavities or ceiling cable tray grids. Heavy-duty IP44 modular floor boxes (Grommets) installed beneath workstations deliver clean mains power, isolated UPS lines, and dual Cat6 data drops to each desk. In multi-storey commercial towers, 160A–400A copper or aluminum busbar trunking risers provide modular plug-in tap-off disconnects for each floor.

Commercial distribution boards integrate power factor correction (PFC) capacitor banks with harmonic filters, alongside fire alarm trip relays that instantly isolate HVAC ventilation systems during emergency evacuations.

As the certified ElektrikçiGO electrician network, we deliver complete apartment, villa, and commercial electrical rewiring projects across all districts of Istanbul's Asian Side with certified technicians. Every wiring run, panel assembly, junction overhaul, and earthing installation carries our official 1 Year Workmanship Guarantee. Work begins only after a transparent written project specification and fixed price quote are approved, with zero surprise cost additions throughout the project.

Upon project handover, every wall socket undergoes loop impedance verification, live-neutral voltage balancing, and 30 mA RCD trip speed certification using Fluke digital instruments. The homeowner receives an official Technical Handover Report detailing the as-built circuit layout and breaker map. For urgent electrical loss, our emergency electrician dispatch fleet operates 24/7.

The band below is the published 2026 list. It is an estimate. The binding figure is written on site after measurement, and the work starts after that.

Service covers the neighborhoods of Istanbul's 39 districts. Not the whole of Turkey. A survey is not a binding quote.